Drivers/net/phy/marvell.c
WebFrom: Krzysztof Kozlowski To: "Igor Russkikh" , "David S. Miller" , "Eric Dumazet" , "Jakub Kicinski" , "Paolo Abeni" , "Simon Horman" , "Andrew … WebMar 17, 2024 · The Marvell PHY can blink the LEDs, simple on/off. All LEDs blink at the same rate, and the reset default is 84ms per blink, which is around 12Hz. Signed-off-by: Andrew Lunn Signed-off-by: Christian Marangi --- drivers/net/phy/marvell.c 36 …
Drivers/net/phy/marvell.c
Did you know?
WebNetdev Archive on lore.kernel.org help / color / mirror / Atom feed From: Krzysztof Kozlowski To: "Igor Russkikh" , "David … WebFeb 20, 2024 · Add basic support for the Marvell 88X2222 multi-speed ethernet transceiver. This PHY provides data transmission over fiber-optic as well as Twinax copper links. The 88X2222 supports 2 ports of 10GBase-R and 1000Base-X on the line-side interface. The host-side interface supports 4 ports of 10GBase-R, RXAUI, 1000Base-X and 2 ports of …
Weblinux-xlnx/marvell.c at master · Xilinx/linux-xlnx · GitHub Xilinx / linux-xlnx Public master linux-xlnx/drivers/net/phy/marvell.c Go to file Cannot retrieve contributors at this time 3412 lines (2868 sloc) 86.8 KB Raw Blame // SPDX-License-Identifier: GPL-2.0+ /* * drivers/net/phy/marvell.c * * Driver for Marvell PHYs * * Author: Andy Fleming * WebNetdev Archive on lore.kernel.org help / color / mirror / Atom feed * [net-next] net: phy: Adding SGMII support for Marvell 88ee1145 driver @ 2014-10-24 2:47 vndao 2014-10 …
Web*net-next PATCH v6 06/16] net: phy: phy_device: Call into the PHY driver to set LED brightness 2024-03-27 14:10 [net-next PATCH v6 00/16] net: Add basic LED support for switch/phy Christian Marangi ` (4 preceding siblings ...) 2024-03-27 14:10 ` [net-next PATCH v6 05/16] net: phy: Add a binding for PHY LEDs Christian Marangi @ 2024-03 ... Web// SPDX-License-Identifier: GPL-2.0+ /* * Marvell 88x2222 dual-port multi-speed ethernet transceiver. * * Supports: * XAUI on the host side. * 1000Base-X or 10GBase-R on the line side.
WebMar 7, 2024 · From: Andrew Lunn The Marvell PHY can blink the LEDs, simple on/off. All LEDs blink at the same rate, and the reset default is 84ms per blink, which is
WebDec 3, 2024 · I am suspicious the uboot's 88E1512 driver. 1512 was released recently(2024) and there is no information about this, in the uboot's marvell.c driver file. But new uboot source(at the github) code includes the 1512's driver code in marvell.c. Should I just change marvell.c file only? Anyway I want to change 88E1512's mode on the uboot. remote bungalows for saleWeb3)reference petalinux2015.4 PHY driver (drivers\net\phy\marvell.c),i try to modify petalinux2024.1 PHY driver marvell.c and phy_device.c,with printk ,in linux2024.1 all the 88e1512 register is the same as 2015.4,but if 1Gbps,it just link up,and remain with RX errors 4)PS 88e1512 phy address is 0,mode is RGMII to copper,here is my dts &gem0 { profinet to profibusWebFrom: Krzysztof Kozlowski To: "Igor Russkikh" , "David S. Miller" , "Eric Dumazet" … profinet timeoutWeb11 * under the terms of the GNU General Public License as published by the profinet to profibus paWebMar 20, 2024 · Intending to use Marvell Alaska 88E1512 Phy physical 1 with a 1 Gbe RGMII Address =0 and Phy 2 100 MbE SGMII Address = 0 and trying to get a feel of changes … profinet system architecturehttp://plrg.eecs.uci.edu/git/?p=firefly-linux-kernel-4.4.55.git;a=blob;f=drivers/net/phy/marvell.c;h=d2ede5ff9fffc5e70136207738c7fada30ca31e4;hb=a4fb2122f1fc4a22bd6a5b8a195b952c2d31c54d profinet toolWebTry enabling these options after running: petalinux-config -c u-boot -> Device Drivers -> Ethernet PHY (physical media interface) support -> Marvell Ethernet PHYs support petalinux-config -c u-boot -> Device Drivers -> Ethernet PHY (physical media interface) support -> Marvel MV88E61xx Ethernet switch PHY support petalinux-config -c u-boot -> … remote bush country of australia